Robotics Lab

Robotics Lab: Explore Boards in 3D

Explore eight boards from Arduino, Espressif and Raspberry Pi. Use Robotics Lab to inspect components in 3D, assemble a board or wire a working circuit.

Building the board…

01Workbench

Robotics Lab circuit workbench

Wire sensors, motors and displays to a board, then press Run to simulate the circuit. Start with a guided Robotics Lab mission or build your own circuit in Free Build.

  • Guided circuit missions

    Step-by-step builds — blink an LED, read a sensor, drive a motor.

  • Pin-to-pin wiring

    Click two pins to connect them. Robotics Lab checks the connections before power-up.

  • Full-screen workbench

    Press Full screen to give the Robotics Lab workbench the whole display.

02Lesson

Robotics Lab: Arduino Nano Lesson and Pinout

Select a board in Robotics Lab to see its specifications, pin functions and component guide.

Board overview

Robotics Lab board guide · Arduino · 2008

The Arduino Nano packs the same brain as the Arduino Uno onto a board the size of a USB stick. Its legs plug straight into a breadboard, which makes it a favourite for small robots, remote controls and wearables. You program it over USB from the Arduino IDE.

Clock
16 MHz
Flash
32 KB
RAM
2 KB
GPIO pins
22
Logic level
5 V
Price
≈ $4–25

Specs

Compare the electrical specs with other Robotics Lab boards. See the hardware references.

Microcontroller
ATmega328P (8-bit AVR)
Clock speed
16 MHz
Flash memory
32 KB (2 KB used by the bootloader)
RAM
2 KB
EEPROM
1 KB
Digital pins
14 (D0–D13), 6 with PWM
Analog inputs
8 (A0–A7), 10-bit
Logic level
5 V
Power
USB 5 V or VIN 7–12 V
Current per pin
20 mA recommended (40 mA absolute max)
USB
Mini-B, FT232RL bridge (CH340 on clones)
Size
43.2 × 17.8 mm, about 7 g

What’s on the board

14 parts match the numbered labels in Robotics Lab. Click one and the camera flies to it.

Strengths and pitfalls

Use these trade-offs when choosing a board in Robotics Lab.

Strengths

  • Plugs straight into a breadboard — no extra wiring needed
  • Runs the same sketches and libraries as the Uno
  • Two more analog inputs than the Uno (A6 and A7)
  • Small and light enough to fit inside any robot

Watch out

  • 5 V logic: connect 3.3 V sensors and modules through a level shifter, or you can burn them out.
  • Never power motors or servos from the board's 5V pin — give them their own supply and join the grounds (GND).
  • One pin can supply only about 20 mA: an LED always needs a resistor, a motor always needs a driver.
  • A6 and A7 are analog inputs only — pinMode and digitalWrite do nothing on them. The 3V3 pin gives just 50 mA.

Pins

Learn which pins to use on the Robotics Lab workbench.

Power

Over USB the board gets 5 V. Without a computer, feed 7–12 V into VIN or a regulated 5 V into the 5V pin. 3V3 is a weak 3.3 V output (50 mA max), GND is the common ground.

Digital pins

D0–D13 work as inputs and outputs with 0 V and 5 V levels. PWM (analogWrite) is available on D3, D5, D6, D9, D10 and D11. D0 and D1 talk to the computer — best leave them alone.

Analog inputs

A0–A7 measure a voltage from 0 to 5 V and return a number from 0 to 1023. A0–A5 can also be used as ordinary digital pins; A6 and A7 are analog inputs only.

I²C and SPI buses

I²C: A4 is SDA, A5 is SCL (displays, gyros, sensors). SPI: D11 is MOSI, D12 is MISO, D13 is SCK, D10 is SS (radio modules, SD cards).

Interrupts and reset

D2 and D3 can react to a signal instantly (attachInterrupt) — handy for wheel encoders. RST restarts the board when it is connected to GND.

Hover over a pin in the Robotics Lab viewer to see its name and function.

  • Power
  • Ground
  • Digital
  • Analog
  • Buses: UART, I²C, SPI
  • Control: RESET, EN, BOOT
  • Not connected

First code

Try the Robotics Lab starter example on your physical board.

First sketch: blink the "L" LED Arduino C++
// Board: Arduino Nano, processor: ATmega328P.// If a clone refuses to upload, pick "ATmega328P (Old Bootloader)".const int LED = LED_BUILTIN;   // the built-in "L" LED on pin D13void setup() {  pinMode(LED, OUTPUT);        // make D13 an output  Serial.begin(9600);          // open the USB link to the computer}void loop() {  digitalWrite(LED, HIGH);     // LED on  Serial.println("On");        // message for the Serial Monitor  delay(500);                  // wait half a second  digitalWrite(LED, LOW);      // LED off  Serial.println("Off");  delay(500);}

Where it shines

Use the Robotics Lab workbench to plan the wiring for a project.

  1. The brain of a small two-motor robot with a motor driver
  2. A line-following robot with reflectance sensors
  3. A handheld remote with a joystick and an nRF24L01 radio
  4. A weather station with I²C sensors and a tiny display
  5. Driving the servos of a small robot arm

Board background

See how this hardware fits into the Robotics Lab board collection.

The Arduino Nano appeared in 2008. It was designed by Gravitech so the board could plug into a breadboard like an ordinary chip.

The Nano has two more analog inputs than the Uno: the flat ATmega328P package has pins A6 and A7 that the big through-hole chip lacks.

The board weighs about 7 grams — less than a single AAA battery.

Practice with this board

Try the same board in these Robotics Lab activities.

Sources

Manufacturer and hardware project documentation.

03Quiz & assembly

Robotics Lab: Component Quiz and Soldering

Use the 3D models in Robotics Lab to identify components, place them on the board and practice soldering. Both exercises work with all eight boards.

Quiz · about a minute

Identify components on a 3D board

Robotics Lab names a part for you to find on the model. Rotate the board, zoom in and flip it over, just like the real thing.

  1. 1

    Read the question. “Find the microcontroller — the brain of the board.”

  2. 2

    Click the part. Not sure? Take a hint, or skip and see the answer.

  3. 3

    See your score. Only first-try answers without a hint count.

Assembly · a few minutes

Assemble and solder a board

Open the Robotics Lab assembly kit to take the board apart into a tray of components. Put every chip, connector and header back where it belongs and solder it down.

  1. 1

    Pick a part from the tray. Chips, connectors, headers, buttons.

  2. 2

    Place it on its footprint. The pads on the bare board show where it goes.

  3. 3

    Solder it in. When the last joint is done, the board is whole again.

04Compare

Robotics Lab: Compare All Eight Boards

Compare processors, memory, pins and logic voltage to choose a board for your project. Select a row to open that board in Robotics Lab.

Robotics Lab lists typical street prices, which vary by seller. “Logic” is the voltage of the I/O pins — never feed 5 V into a 3.3 V board.

Robotics Lab FAQ

What can I do in Robotics Lab?

Rotate eight 3D circuit boards, inspect their pins and components, practice assembling and soldering a board, and wire virtual circuits in the browser.

Which boards can I explore in Robotics Lab?

The lab includes the Arduino Uno R3, Arduino Nano, Arduino Mega 2560 R3, ESP32 DevKit V1, NodeMCU, Raspberry Pi Pico, STM32 Blue Pill and Raspberry Pi 4 Model B.

Does Robotics Lab require a physical board or an account?

The virtual lab runs without an account or physical hardware. The 3D viewer and simulator need JavaScript and WebGL 2. Board specifications and lessons are readable without starting the viewer.

How do I get started with circuit simulation?

Open the circuit workbench and choose the first LED mission. Follow its wiring steps, press Run and watch the LED blink. Free Build lets you choose and connect your own components.

How does Robotics Lab score the component quiz?

A correct first answer without a hint earns one point. A correct answer after a retry or hint still lets you complete the question. Your best score is saved in this browser.

Can I use Robotics Lab wiring on real hardware?

Use the simulator to practice and understand the connections. Before wiring a physical board, check the manufacturer’s documentation for its pinout, voltage limits and power requirements.