Robotics Lab

Robotics Lab: Explore Boards in 3D

Explore eight boards from Arduino, Espressif and Raspberry Pi. Use Robotics Lab to inspect components in 3D, assemble a board or wire a working circuit.

Building the board…

01Workbench

Robotics Lab circuit workbench

Wire sensors, motors and displays to a board, then press Run to simulate the circuit. Start with a guided Robotics Lab mission or build your own circuit in Free Build.

  • Guided circuit missions

    Step-by-step builds — blink an LED, read a sensor, drive a motor.

  • Pin-to-pin wiring

    Click two pins to connect them. Robotics Lab checks the connections before power-up.

  • Full-screen workbench

    Press Full screen to give the Robotics Lab workbench the whole display.

02Lesson

Robotics Lab: Arduino Mega 2560 R3 Lesson and Pinout

Select a board in Robotics Lab to see its specifications, pin functions and component guide.

Board overview

Robotics Lab board guide · Arduino · 2010

The big brother of the Arduino Uno: the same simple language and the same shields, but more than three times the pins and eight times the memory. Reach for a Mega when a robot needs lots of motors, sensors and displays at once — a walking robot, a robotic arm or a 3D printer.

Clock
16 MHz
Flash
256 KB
RAM
8 KB
GPIO pins
54
Logic level
5 V
Price
≈ $45

Specs

Compare the electrical specs with other Robotics Lab boards. See the hardware references.

Microcontroller
ATmega2560 (8-bit AVR)
Clock speed
16 MHz
Flash memory
256 KB (8 KB used by the bootloader)
RAM / EEPROM
8 KB / 4 KB
Digital pins
54, of which 15 with PWM
Analog inputs
16 (10-bit ADC)
Serial interfaces
4 hardware UARTs, I²C, SPI
Logic voltage
5 V
Current per pin
20 mA (absolute maximum 40 mA)
Power
USB 5 V or 7–12 V via barrel jack / Vin
USB
USB-B connector, ATmega16U2 bridge
Size and weight
101.6 × 53.3 mm, 37 g

What’s on the board

16 parts match the numbered labels in Robotics Lab. Click one and the camera flies to it.

Strengths and pitfalls

Use these trade-offs when choosing a board in Robotics Lab.

Strengths

  • 70 pins: 54 digital and 16 analog — enough for a big robot
  • Four hardware UARTs: GPS, Bluetooth and debugging at the same time, no SoftwareSerial needed
  • Compatible with Arduino Uno shields and sketches
  • 5 V logic works directly with most classroom sensors and modules

Watch out

  • A pin supplies no more than 20 mA: power motors and servos from a separate supply through a driver, with the grounds connected together.
  • 3.3 V modules (ESP8266, nRF24L01, many sensors) must not be wired straight to the 5 V pins — use a level shifter.
  • SPI and I²C are not where they are on the Uno: SPI is on pins 50–53, I²C on 20 and 21. Old shields that expect pins 11–13 and A4/A5 may not work.
  • Feed 7–12 V into the barrel jack. Above that the regulator runs hot; below that the board gets less than 5 V.

Pins

Learn which pins to use on the Robotics Lab workbench.

Power

5V and 3.3V are outputs for sensors (no more than 50 mA from 3.3V). GND is the common "minus". Vin carries whatever voltage arrives at the barrel jack. The double-row header has two more 5 V contacts at the top and two GND contacts at the bottom.

Digital pins and PWM

Pins 0–53 work as inputs or outputs with 0 V and 5 V levels. PWM (analogWrite) is available on pins 2–13 and 44–46. External interrupts are on 2, 3, 18, 19, 20 and 21.

Analog inputs

A0–A15 measure 0–5 V with 10-bit resolution (0–1023). They can also be used as ordinary digital pins 54–69.

Serial ports

Serial (pins 0, 1) is tied to USB — keep those pins free if you use the Serial Monitor. Serial1 is on 19 (RX) and 18 (TX), Serial2 on 17 and 16, Serial3 on 15 and 14.

I²C and SPI

I²C: 20 (SDA) and 21 (SCL), duplicated next to AREF. SPI: 50 (MISO), 51 (MOSI), 52 (SCK), 53 (SS) and on the ICSP header — not on 10–13 as on the Uno.

Hover over a pin in the Robotics Lab viewer to see its name and function.

  • Power
  • Ground
  • Digital
  • Analog
  • Buses: UART, I²C, SPI
  • Control: RESET, EN, BOOT
  • Not connected

First code

Try the Robotics Lab starter example on your physical board.

Blink the LED and listen to a second serial port Arduino C++
// The Mega has four hardware serial ports: Serial (USB), Serial1, Serial2, Serial3.// We blink the built-in LED "L" and forward everything a module sends// on Serial1 (for example a Bluetooth HC-05 or a GPS) to the Serial Monitor.// Module wiring: its TX -> pin 19 (RX1), its RX -> pin 18 (TX1), GND -> GND.const int LED = 13;            // built-in LED "L"unsigned long lastBlink = 0;   // time of the last blinkbool ledOn = false;void setup() {  pinMode(LED, OUTPUT);  Serial.begin(9600);          // link to the computer over USB  Serial1.begin(9600);         // link to the module on pins 18 and 19  Serial.println("Mega is ready!");}void loop() {  // Blink without delay() so no incoming data is missed  if (millis() - lastBlink >= 500) {    lastBlink = millis();    ledOn = !ledOn;    digitalWrite(LED, ledOn);  }  // Module -> computer  if (Serial1.available()) Serial.write(Serial1.read());  // Computer -> module  if (Serial.available()) Serial1.write(Serial.read());}

Where it shines

Use the Robotics Lab workbench to plan the wiring for a project.

  1. Hexapod robot: 18 servos through a driver, sensors on the remaining pins
  2. Robotic arm with joysticks, limit switches and a display
  3. The brain of a 3D printer or CNC machine (a RAMPS board plugs on top as a shield)
  4. A large weather station or smart greenhouse with dozens of sensors
  5. LED matrices and panels that need lots of pins

Board background

See how this hardware fits into the Robotics Lab board collection.

Thousands of home-built RepRap 3D printers ran on an Arduino Mega with a RAMPS shield — this board helped make desktop 3D printing mainstream.

The ATmega2560 has one hundred leads and 86 of them can be inputs/outputs, but only 70 are brought out to the headers.

Analog inputs A0–A15 double as digital pins 54–69: digitalWrite(A0, HIGH) works.

Practice with this board

Try the same board in these Robotics Lab activities.

Sources

Manufacturer and hardware project documentation.

03Quiz & assembly

Robotics Lab: Component Quiz and Soldering

Use the 3D models in Robotics Lab to identify components, place them on the board and practice soldering. Both exercises work with all eight boards.

Quiz · about a minute

Identify components on a 3D board

Robotics Lab names a part for you to find on the model. Rotate the board, zoom in and flip it over, just like the real thing.

  1. 1

    Read the question. “Find the microcontroller — the brain of the board.”

  2. 2

    Click the part. Not sure? Take a hint, or skip and see the answer.

  3. 3

    See your score. Only first-try answers without a hint count.

Assembly · a few minutes

Assemble and solder a board

Open the Robotics Lab assembly kit to take the board apart into a tray of components. Put every chip, connector and header back where it belongs and solder it down.

  1. 1

    Pick a part from the tray. Chips, connectors, headers, buttons.

  2. 2

    Place it on its footprint. The pads on the bare board show where it goes.

  3. 3

    Solder it in. When the last joint is done, the board is whole again.

04Compare

Robotics Lab: Compare All Eight Boards

Compare processors, memory, pins and logic voltage to choose a board for your project. Select a row to open that board in Robotics Lab.

Robotics Lab lists typical street prices, which vary by seller. “Logic” is the voltage of the I/O pins — never feed 5 V into a 3.3 V board.

Robotics Lab FAQ

What can I do in Robotics Lab?

Rotate eight 3D circuit boards, inspect their pins and components, practice assembling and soldering a board, and wire virtual circuits in the browser.

Which boards can I explore in Robotics Lab?

The lab includes the Arduino Uno R3, Arduino Nano, Arduino Mega 2560 R3, ESP32 DevKit V1, NodeMCU, Raspberry Pi Pico, STM32 Blue Pill and Raspberry Pi 4 Model B.

Does Robotics Lab require a physical board or an account?

The virtual lab runs without an account or physical hardware. The 3D viewer and simulator need JavaScript and WebGL 2. Board specifications and lessons are readable without starting the viewer.

How do I get started with circuit simulation?

Open the circuit workbench and choose the first LED mission. Follow its wiring steps, press Run and watch the LED blink. Free Build lets you choose and connect your own components.

How does Robotics Lab score the component quiz?

A correct first answer without a hint earns one point. A correct answer after a retry or hint still lets you complete the question. Your best score is saved in this browser.

Can I use Robotics Lab wiring on real hardware?

Use the simulator to practice and understand the connections. Before wiring a physical board, check the manufacturer’s documentation for its pinout, voltage limits and power requirements.